Install on Windows (preview)
The Windows installer is in preview. Mac and Linux are the proven paths today. Try Windows on a test computer first, and tell us what you find.
Check Requirements first.
1. Check the computer
Install Ollama 0.40 or newer from ollama.com/download and start it. Version 0.9 is older than 0.40: if ollama --version prints 0.9 or lower, install the current one. Then, in PowerShell, pull the model:
ollama --version
ollama pull gemma4:12b-it-qat
Find this computer's IPv4 address on the camera network. ipconfig lists the addresses. If the computer has several networks or a VPN, use the address on the same network as the cameras. Use an address that does not change (a static address or a DHCP reservation), because the cameras remember it.
2. Install the Local link
Download the PowerShell installer from anava.ai/edge/local: choose the Windows tab. The page shows the command with the current version filled in.
Open PowerShell as an administrator: choose Start, type PowerShell, right-click it and choose Run as administrator. It opens in C:\WINDOWS\system32, so go to your Downloads folder first, then run the installer:
cd $env:USERPROFILE\Downloads
powershell -ExecutionPolicy Bypass -File .\install-anava-local.ps1 -Version VERSION -AdvertiseHost YOUR-LAN-IP
Replace VERSION with the version the page shows, and YOUR-LAN-IP with this computer's address on the camera network, for example 192.168.1.20.
If PowerShell says the file does not exist, the installer is in another folder (Downloads can be inside OneDrive, for example). Open that folder in File Explorer, copy its path from the address bar, and go there with cd "FOLDER", putting the path in place of FOLDER.
What this does, before you run it:
- It needs an administrator PowerShell. It will not work in an ordinary one.
- It registers a Windows service named
AnavaLocalLink. The service starts at boot, starts again after a failure, and runs with nobody signed in. - It keeps its settings in
C:\ProgramData\Anava\local-link. Only SYSTEM and Administrators can open that folder. - It does not change Ollama or your models.
Keep the computer on and awake. In Windows power settings, set it never to sleep. If it sleeps, the AI stops until it wakes.
To use a different model, add -Model OLLAMA-TAG, with the tag you pulled in place of OLLAMA-TAG. See Requirements.
Installers up to v2026.11.4 leave two steps to you. A newer installer does both itself, so skip them if the page shows a newer version.
Open Windows Firewall for the cameras. Without this, each camera's Test connection fails:
New-NetFirewallRule -DisplayName "Anava Local link" -Direction Inbound -Protocol TCP -LocalPort 9443 -Action Allow -Profile Private,Domain
The rule works on a network that Windows calls Private or Domain. Get-NetConnectionProfile shows what Windows calls this one. If it says Public, change the network to Private in Windows network settings, or the cameras stay blocked.
A camera network with no router shows as an unidentified network, and Windows may not let you change it. Then let in that network only:
New-NetFirewallRule -DisplayName "Anava Local link (camera network)" -Direction Inbound -Protocol TCP -LocalPort 9443 -Action Allow -Profile Public -RemoteAddress LocalSubnet
Make this PowerShell window find the program. Without this, PowerShell says anava-local-gateway is not recognized. Type it again in any new window:
$env:Path += ";C:\Program Files\Anava\LocalLink"
3. Check it
In an administrator PowerShell:
anava-local-gateway service status
anava-local-gateway status --config "C:\ProgramData\Anava\local-link\gateway.json"
status shows the model, the queue, the cameras it has seen and each licence with its end date. It never prints a secret.
Differences from Mac and Linux
- There is no
sudo. Run everyanava-local-gatewaycommand in an administrator PowerShell. - The settings folder is
C:\ProgramData\Anava\local-link. - With installers up to v2026.11.4, you add the firewall rule and the PATH line yourself (step 2).
- The token goes in from the clipboard. You do not need to save it in a file. See Licence and cameras.
- The link keeps no log file on Windows. If it does not start, see Troubleshooting.
- Ollama on Windows starts when a person signs in, not at boot. After a restart, someone has to sign in or the AI stays off.
Next step
Get a licence and pair your cameras
Related: anava.ai/edge/local